On the face of it they looked good value and they advertised the wheels with an external rim width of either 23mm or 25mm. I ordered a set of carbon wheels for my TT/Tri bike. Watch on YouTubeĪ video presentation covering the frame, accessories and the technical aspects is available below.Beware. Trifox and Ican have adopted similar approaches and done quite well as a result. Manufacturing quality is on a par with the likes of Cannondale, Giant etc whose frames cost significantly more.Įlves would probably do better by dropping the price of the frame slightly, removing the ceramic bottom bracket and including handlebars. It should be noted that at the price point, the frame does represent good value for money. The final execution of the manufacturing has some good points but is let down in some areas. Overall, the frame is nothing more than average and possibly slightly below. Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal Elves Vanyar Internal There was nothing in in the frame that jumped out as an immediate failure point but from a manufacturing exercise, there are better frames out there. Internally, the frame exhibited signs of tenting, displacement voids and there were large areas where excess resin had been forced out. Elves Vanyar Elves Vanyar Elves Vanyar Front Fork The fork is set up for single caliper rim brakes, the hole alignment was good in comparison to the dropout datum. The steerer tube has plenty of excess and will require cutting for all applications. Both bearing seats are tapered do fit into the frame. The bottom bearing is approximately 1.5″ whilst the top is 1.1/4″. It has a tapered headset arrangement, the bearings for this are included. Elves Vanyar Elves Vanyar Elves Vanyar Elves Vanyar Elves Vanyar Elves Vanyar Seatpost Front Fork The access mechanism is from beneath so no specialist tools or hacksawed off hex keys are required. One bolt is effectively fixed, micro adjustment is performed on the other. The seat clamp is round profile metal compatible, for carbon rails, you will likely need an alternative clamp. The fasteners are of reasonable quality, the fastener markings indicate they are of Chinese origin. The seatpost mount is infinitely adjustable from approximately +/- 30 degrees. An internal inspection of the frames showed no visible defects. It has a round profile and is made of carbon fibre. Elves Vanyar Elves Vanyar Elves Vanyar Elves Vanyar Elves Vanyar Elves Vanyar Elves Vanyar Heasdset Elves Vanyar Heasdset Seatpost The location on the other side was comparatively much thicker. In addition, the lower bearing seat had a very thin sidewall to locate the bearing. The seats did have some surface defects (voids) This would need correcting or an increase in preload to account for this would be required. The fit on the upper bearing was quite slack to the point where it’s likely the rider would feel a click under some cornering loads. The rear gear hanger fit was poor Elves Vanyar Elves Vanyar Elves Vanyar Elves Vanyar Elves Gear Hanger and dropoutsĪn area of real concern was around the headset. There were some areas where the attention to detail and final execution were lacking. There was little angular deviation or distortion. The geometry accuracy across the frame between datum and accessory points was very good. The bottom bracket on this bike frame was quite irregular, there were visible gouges in the seats, the aperture was slightly undersized, there was some distortion around the circumference. Elves Vanyar Elves Vanyar Frame manufacturing and qualityĮlves supply the frame with a headset, ceramic thread together bottom bracket, seat post and forks. An interesting feature of the frame is the claimed one piece molding for manufacture, indicating the frame has no joints. The retail price of the frame was $1000 USD. This frame was a rim brake model with a single caliper mounting point. This frame was purchased by a viewer of the Hambini YouTube channel and sent for assessment. Some of their literature suggests Taiwan, other markings and those on the bike frame suggest China and Hong Kong. The origin of Elves is not totally clear.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |